AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Neat receipts calibration sheet pdf10/25/2022
A Warning statement identifies conditions or practices that could result in injury or death. Some features provided by the Meter are: A dual vacuum fluorescent display that allows two properties of an input signal to be displayed at the same time (e.g., ac voltage in one display and frequency in the other) 5-1/2 digit resolution True-rms ac 2, 4 wire resistance or patented 2x4 wire resistance measurement technique 200 mv to 1000 Vdc range with 1 μv sensitivity 200 mv to 750 Vac rms with 1 μv sensitivity 200 Ω to 100 MΩ with 1 mω sensitivity 200 μa to 10 Adc with 1 na sensitivity 20 ma to 10 Aac with 100 na sensitivity Frequency measurements from 20 Hz to 1 MHz Continuity and diode test Measurement rates of 2.5, 20 and 100 samples/second (slow, medium and fast, respectively) Front-panel setup key for single key access to saved setups A compare mode to determine if a measurement is within defined limits Remote operation via the RS-232 interface Closed-case calibration (no internal calibration adjustments) Safety Information This section addresses safety considerations and describes symbols that may appear on the Meter or in the manual. For portability, the Meter includes a carrying handle that also serves as a bail for bench-top operation. NEAT RECEIPTS CALIBRATION SHEET PDF MANUALThe multiple measurement functions, plus the RS-232 remote interface, make the Meter an ideal candidate for precision manual measurements and use in automated systems. NEAT RECEIPTS CALIBRATION SHEET PDF VERIFICATIONIEC Measurement Category (CAT) Levels Replacing the Line Power Fuse Replacing the Current-Input Fuses Display Elements Direct and Alternating Voltage Verification Test Setup Wire Ohms Test Setup Wire Ohms Test Setup Less than 2 Amps Direct and Alternating Current Test Setup Amps and Greater Direct and Alternating Current Test Setup Front-Panel Assembly Chassis Assembly vĩ Chapter 1 Introduction and Specifications Title Page Introduction Safety Information Symbols General Safety Summary Description of IEC Measurement Categories Manual Set About This Manual Operating Instructions Accessories General Specifications Voltage Dimensions Display Environment Safety EMC Triggering Math Functions Electrical Remote Interfaces Warranty Electrical Specifications DC Voltage Specifications AC Voltage Specifications Resistance DC Current AC Current Frequency Continuity Diode Testġ1 Introduction and Specifications Introduction 1 Introduction The Fluke 8808A Digital Multimeter (hereafter referred to as the Meter) is a 5-1/2 digit dual-display multimeter designed for bench-top, field service, and system applications. Safety and Electrical Symbols Accessories Line Voltage to Fuse Rating Required Test Equipment Direct Voltage Verification Steps Alternating Voltage Verification Steps Wire Ohms Verification Steps Wire Ohms Verification Steps Direct Current Verification Steps Alternating Current Verification Steps Frequency Verification Steps Adjustment Steps Front-Panel Assembly Chassis Assembly iiiħ List of Figures Figure Title -1. NEAT RECEIPTS CALIBRATION SHEET PDF HOW TOAll product names are trademarks of their respective companies.ģ Table of Contents Chapter Title Introduction and Specifications Introduction Safety Information Symbols General Safety Summary Description of IEC Measurement Categories Manual Set About This Manual Operating Instructions Accessories General Specifications Voltage Dimensions Display Environment Safety EMC Triggering Math Functions Electrical Remote Interfaces Warranty Electrical Specifications DC Voltage Specifications AC Voltage Specifications Resistance DC Current AC Current Frequency Continuity Diode Test General Maintenance Introduction iĤ 8808A Calibration Manual General Maintenance Information Required Equipment Static Safe Handling Cleaning Storing and Shipping the Meter Power Considerations Selecting the Line Voltage Replacing the Fuses Line-Power Fuse Current-Input Fuses If the Meter Does Not Turn On Display Tests Performance Verification and Calibration Introduction Required Equipment Direct Voltage Verification Alternating Voltage Verification Wire Ohms Verification Wire Ohms Verification Direct Current Verification Alternate Current Verification Frequency Verification Adjustment (Calibration) Equipment for Calibration Adjustment Process Front Panel Adjustments RS-232 Calibration (Manual) RS-232 Calibration (Automatic) Calibration Points List of Replaceable Parts Introduction How to Obtain Parts How to Contact Fluke Parts Lists iiĥ List of Tables Table Title -1. Specifications are subject to change without notice. 1 8808A Digital Multimeter Calibration Manual October Fluke Corporation.
0 Comments
Read More
Leave a Reply. |